CUMMINS INPOWER
CUMMINS INPOWER the link:https://www.autovci.com/cummins-inpower
CUMMINS INPOWER
Version:10.2
Languages:English
OS:VISTA,Win7 x32,Win98,Windows 8 x32,WinJapan,WinNT,WinXP
Function:
1.Direct connection capability from a personal computer to PowerCommand genset controls,transfer controls,and system controls;For details on devices supported refer Technical Details tab.
2.Plot critical parameters in a strip chart format, and export data to 3rd party software tools for manipulation and viewing.
3.Configurable for units of measurement, and level of user access (read only, read/change values,administrator).
4.Generates reports of monitored data
5.Connection to generator set or transfer switch controls via modem or to multiple controls via PowerCommand (LonWorks)network.
6.Allows released firmware upgrades on Power Command genset controls.
7.Allows the monitored equipment to send alarm information to a connected computer.
8.Simulate fault conditions in genset controls in compliance to NFPA 110 requirements to demonstrate functionality of the controller and monitoring equipment in a facility.
9.Adjustment of nearly every adjustment parameter within the connected control system, including parameters such as voltage and frequency levels, gains, protection set-points and other values.
10.Viewing of equipment history, fault codes, and data associated with fault codes.
11.Convenient programming of configurable inputs in the controllers.
Cummins InPower Pro v11.2 with Activator
Installation Instructions:
1. This patch shall work for V11InPower Pro, V11 InPower Lite, and V11 InPower Onan only. One of these Tools should be installed on the target machine before applying the patch.
2. Patch V11 supports only Windows XP, Vista, Windows 7, Windows 8 & 8.1 operating systems.
3. Patch V11 can be installed with and without administrative privileges. However, this would also depend on the policies on the system. If the path where the V11 version of the tool is installed requires administrative rights, then installation of the Patch V11 will also need admin rights for installation.
4. All above mentioned tools and their utilities should be closed before installing the patch.
5. The Patch is uninstalled automatically when the Main V11 application is uninstalled.
6. If multiple tools are to be installed on a particular machine then it is recommended to install the Patch after ALL the tools are installed. Patch will have NO effect if another tool is installed post patch installation.
New features & Enhancements
1. Support of 40 field and factory features each. Previously 20 features were supported.
2. Engine serial number and engine model number has been added for Dynasty controller while calibrating in the MFG Tool. Informative message shown if there is an Active shutdown fault when Calibration is attempted on PCC3200, G-Drive and PCC2100.
Issue fixes
1. Issue fix for the Compare Utility with Dominion and Dynasty Compare utility was not showing proper comparison of capture files with Dominion and Dynasty. This issue has been resolved now.
2. Corrected the Consumer device dfa files (20.dfa,16.dfa,54.dfa,26.dfa)
3. Issue fix for the Lonmaker on Windows 8 while adding the site.Tool was unable to add the site on windows 8 when Lonmaker is installed because LonMaker does not support Windows 8 OS as yet. This issue has been taken care in Tools.
4. Updated the Tool for resolving the Client CD version conflict during PCC1302 upgrade.Client CD Version has a conflict with the tool while calibrating the PCC1302. This issue has been taken care now.
5. Issues fixed for 64 Bit (windows 8) machines for Utilities - InCal Extractor and SPEED Upload Download utility.
6. Issue fix for the font size which was too small on some of the PS4 ultrabook machines (windows 8.1).
If you have any problem, please do not hesitate to contact us.
Email ：autovci@outlook.com
CUMMINS INPOWER
Version:10.2
Languages:English
OS:VISTA,Win7 x32,Win98,Windows 8 x32,WinJapan,WinNT,WinXP
Function:
1.Direct connection capability from a personal computer to PowerCommand genset controls,transfer controls,and system controls;For details on devices supported refer Technical Details tab.
2.Plot critical parameters in a strip chart format, and export data to 3rd party software tools for manipulation and viewing.
3.Configurable for units of measurement, and level of user access (read only, read/change values,administrator).
4.Generates reports of monitored data
5.Connection to generator set or transfer switch controls via modem or to multiple controls via PowerCommand (LonWorks)network.
6.Allows released firmware upgrades on Power Command genset controls.
7.Allows the monitored equipment to send alarm information to a connected computer.
8.Simulate fault conditions in genset controls in compliance to NFPA 110 requirements to demonstrate functionality of the controller and monitoring equipment in a facility.
9.Adjustment of nearly every adjustment parameter within the connected control system, including parameters such as voltage and frequency levels, gains, protection set-points and other values.
10.Viewing of equipment history, fault codes, and data associated with fault codes.
11.Convenient programming of configurable inputs in the controllers.
Cummins InPower Pro v11.2 with Activator
Installation Instructions:
1. This patch shall work for V11InPower Pro, V11 InPower Lite, and V11 InPower Onan only. One of these Tools should be installed on the target machine before applying the patch.
2. Patch V11 supports only Windows XP, Vista, Windows 7, Windows 8 & 8.1 operating systems.
3. Patch V11 can be installed with and without administrative privileges. However, this would also depend on the policies on the system. If the path where the V11 version of the tool is installed requires administrative rights, then installation of the Patch V11 will also need admin rights for installation.
4. All above mentioned tools and their utilities should be closed before installing the patch.
5. The Patch is uninstalled automatically when the Main V11 application is uninstalled.
6. If multiple tools are to be installed on a particular machine then it is recommended to install the Patch after ALL the tools are installed. Patch will have NO effect if another tool is installed post patch installation.
New features & Enhancements
1. Support of 40 field and factory features each. Previously 20 features were supported.
2. Engine serial number and engine model number has been added for Dynasty controller while calibrating in the MFG Tool. Informative message shown if there is an Active shutdown fault when Calibration is attempted on PCC3200, G-Drive and PCC2100.
Issue fixes
1. Issue fix for the Compare Utility with Dominion and Dynasty Compare utility was not showing proper comparison of capture files with Dominion and Dynasty. This issue has been resolved now.
2. Corrected the Consumer device dfa files (20.dfa,16.dfa,54.dfa,26.dfa)
3. Issue fix for the Lonmaker on Windows 8 while adding the site.Tool was unable to add the site on windows 8 when Lonmaker is installed because LonMaker does not support Windows 8 OS as yet. This issue has been taken care in Tools.
4. Updated the Tool for resolving the Client CD version conflict during PCC1302 upgrade.Client CD Version has a conflict with the tool while calibrating the PCC1302. This issue has been taken care now.
5. Issues fixed for 64 Bit (windows 8) machines for Utilities - InCal Extractor and SPEED Upload Download utility.
6. Issue fix for the font size which was too small on some of the PS4 ultrabook machines (windows 8.1).
If you have any problem, please do not hesitate to contact us.
Email ：autovci@outlook.com
Comments
Post a Comment